How to use electric fish machine

How to use electric fish machine

The electric fish machine is a pulsed DC converter that converts a low-voltage and high-current power source into a high-voltage, instantaneous high current.

The composition of the electric fish machine divided into two parts: the first part: the inverter (previous stage); the second part: the rectification pulse discharge (the latter stage).

Part 1: Inverter (previous stage)

It is very important that the electric fish machine should electrically connected to the pre-inverter part of the fish. The front part must have enough output power and match the appropriate output voltage, because only the power of the fishing machine is large enough to improve the electric fish machine. The effect of fishing is to get rich by fishing with electric anglers. If the output power is not large enough, the voltage is higher (that is, the voltage of the transformer is made larger) and the fish cannot be caught. I believe that everyone has seen self-defense stun guns with voltages up to tens of thousands of volts. It can used to call the fish but it has no effect. Because the stun gun power is too small, with no water load. However, the voltage is too low, and the voltage is too low. It has no effect on the fish and can only tickle the fish. Water is resistive and is equivalent to a load. The voltage is too low. The current flowing through the water load is too small. If the voltage is too high, the output internal resistance will increase. This load capacity will reduced again.

Part II: Rectified Pulse Discharge (Post Stage)

Doing a good job in the rear of the fishing machine is the key to successfully making a good fishing machine. The pulse discharge part of the high-frequency fishing machine is the process of discharging the high-voltage direct current after energy storage into the water through the capacitor. The capacitor stores energy instantaneously to discharge into the water to increase the instantaneous power and achieve the instantaneous maximum pulse power to achieve the best fish effect. However, the total power will not change. It will maintain the energy conversion and conservation laws, i.e. the input power is always greater than the output power. A good fishing machine, it is not enough to have a good preamp or a good post. Do not think about how good the rear pole is to amplify the power of the front stage and the actual power discharged from the capacitor. In the water, most of the power consumed, and the power acting on the fish body is only a small part. The rectification can be double-voltage rectification. Bridge rectification is also available. If the transformer output voltage is low. The voltage can increased by double voltage, and bridge rectifier can used if the output voltage of the transformer is high.

Electric fish machine operation method

Electric fish machine operation method

1. Make a dip net and make a metal ring with a radius of about 15 (the ring ire commended to use copper bars, because the copper tube is a metal with good conductivity and acceptable price. Note: Why choose copper without cheap iron, copper Conductivity is better than iron, conductive direct fishing effect) Put on the fishing net as the positive pole. which is what we call dip net, and then make a probe with a radius of 6MM and a length of 35 cm to 45 cm, respectively 2 tops of the bamboo poles of their own custom length. Then connect them with wires. (Note: Wires must also use good lines. Do not use cheap flower lines or too thin wires. Another must use copper wire. Below I teach you how to find high-quality copper wire, the difference between copper and aluminum, peel off the skin of the wire. A little, then use a lighter to burn for a few seconds, if the aluminum wire directly burned, it will turn white and the melted copper wire will not turn white. The back machine recommended using 2.5 square meters to foursquare meters of soft copper wire.

2. Connect the positive and negative stages of the electric fish machine to the positive and negative poles of the 12V battery. If the contact is not good, the self-protection of the fishing device will not work or the discharge current will be small. Then, the two bamboo sticks will copied. The 2 tail wires of the net are respectively connected to the 2 output screw joints of the machine. Note that there is no stable contact, the positive and negative poles divided, the red is positive, the black is negative, and then the above program checked to prevent errors.

3. The high and low-pressure switch on the electric fish machine determined by the shallow water depth at that time. Generally, the low pressure is about 1 meter water depth. If it is higher than the high pressure, it will waste power and cannot used continuously.

4. The key to the fishing effect of the electric fish machine is the frequency adjustment; it is not the best to adjust to the highest effect. this depends on the actual level of operation of the individual, generally the operation method of the medium-power electric fish machine is the frequency adjustment is close Half of the two bamboo rafts are almost 1 meter apart. This is a very good operation. The high-powered back machine has a bamboo raft of 1.6 meters to 2 meters, and the frequency is moderate. The effect is generally good (Note: Why are the two bamboo rafts at the same time? Because the high-frequency machine discharge is mainly a loop between two bamboo rafts. If the bamboo rafts are too close together, the power of the machine will be difficult to play. At this point, many newcomers and people who don't understand or People who have played the traditional low-frequency electric fish machine do not understand, saying that I have been playing for many years without teaching, thinking that the operation mode of the high-frequency machine is the same as that of the traditional bottom frequency machine. In fact, the operation of the low-frequency machine is not high-frequency operation. In the same way, please ask the so-called old players to operate according to the above method. The distance between the bamboo poles is exquisite, and the adjustment of the frequency is the most critical, which directly affects the effect of the machine).

The above method of operating the electric fish machine is commonly used. Because the water quality and temperature of each area are different, the frequency not exactly adjusted. It depends on the player's own practice. According to the high-power, back machine, the two bamboo rafts separated by 1.5 meters to 2 meters. The frequency adjusted to half of the position. The fish's reflection used to adjust the frequency. If the fish between the two poles is easy to run, the frequency should properly opened. Big point, if it is easy to sink, it is necessary properly close the small point. This is my long-term accumulated experience to share with you. Add a little more. Do not let the frequency of the machine reach the maximum. The fish in this range is easy to sink into the water and cannot see. A few meters away from the outside, there are fish that sense a slight power and run. Many novices say that the maximum is not effective, saying that the machine cannot work, but the scientific operation mode that the player does not understand.

Electric fish machine operation method

Electric fish machine operation skills:

1. Connect the positive and negative poles of the 12V battery to the battery clamp of the machine, and then connect the other ends of the two insulated wires of the power grid to the output terminals of the machine.

2. The high and low-pressure switches on the machine determined by the shallow depth of water. High pressure used for deep water and low pressure for shallow water to save energy. The frequency adjustment on the machine is the key to fishing. Proper use adjusts the potentiometer to the proper position, so that the relay emits a crisp sound without sinking, and the fishing effect is best!

3. Hold the bamboo poles and place the two electrodes in the water. The distance between the two poles is 1 to 5 meters (the distance depends on the power of the machine, the distance between the machines is generally 1-2 meters, and the shipboards are generally 3 to 5 meters apart). Continue to press Move the switch, you can corona fish, you can fish by disconnecting the switch!

4. To determine whether there are fish, in general, in addition to the stream, there are fish in the waters, because of the activities of the fish. the water will be very yellow, especially where there are many fish, the water is very awkward, and vice versa, the water is clear, even bottom (Common in winter), there are no fish in all likelihood.

5, the use of manual control switches, small waters electric fish, generally short press, found that the target can be opened a little longer, so that electric fish is more energy-efficient, can greatly extend battery life, large waters should also follow this principle Just to lengthen a little longer boot time.

6. Frequency adjustment, such as a 38000W machine, not the greater the power the better, must adjusted to the appropriate frequency, according to different water quality, different water temperature adjustment.

7. Use a low pressure below one meter in shallow water, and use high pressure when the water depth exceeds one meter, depending on the depth of the water.

8. If the water is relatively clear, use the main frequency, so that the fish will not run. If the water is mixed, use the mixing frequency, so that the fish has the opportunity to surface.

Operation method of clear water and mixed water:

1. The friends who used the electric fish machine know that the effect of the same electric fish machine is very different when it used in very clear water and a little mixed water. Why is this happening because the water and the mixed water are conductive? The rate is different. The conductivity of clean water is relatively low, and the conductivity of mixed water is strong. Therefore, the effect of electric fishing in two kinds of water is definitely different. It is necessary to change the working voltage of electric fish machine to change fishing. Effect.

2. The working voltage of the electric fish machine of Qingshui should be high, and the voltage of the rectification should reach 850V to 1100V. If it is peak voltage, it should be good at 1200V to 1500V. The voltage is high in conductivity. Only the low water has good penetrating power to increase the depth of the electric fish. Another point is to increase the area of the exposed copper in the water line. Both the dip net and the water line simultaneously enlarged.

3, the voltage of the electric fish machine in the mixed water is not too high, the voltage can be 600V to 850V, in this voltage range, it can penetrate the water well, it can have a good fishing effect, if When the high-voltage is used in the mixed water, the fish is very easy to sink into the water. The water is very turbid, and the fish sinks under water and cannot see the fish.

Four, Also, the activity of clear water fish and mixed water fish is different. The fish in clear water is very active and runs very fast. The fish in mixed water is less active. In electric water fishing in clear water, try not to going out of the movement, otherwise the fish will run far, you do not want electricity.

Electric fish machine operation method

Electric fish machine use precautions

One, electronic products are not exposed to water fishing, it is best to protect the rain. In addition, pay attention to the human body cannot touch the electrode two head cannot contact the electrode when the machine works.

2. If the sound of the machine work is obviously small and the lethality is small during the use, it means that the battery power is insufficient. Do not continue to use it to replenish the battery to avoid the battery losing power and damage the battery.

3. It is normal for the machine to generate a certain amount of heat when it is working. (Also, there is no heat in the electrical work.) Please do not cover the heat dissipation of the machine, let the machine dissipate heat and do not open the outer casing of the machine. This can easily damage the internal parts of the machine.

4. This is the most important point; 80% repair machine are because of this. Many customers like to use second level spark to try machine's power, this is very wrong.  Even there is short-circuit protection, protection is not 100%. Just like a car has airbags, but it could not stand often high-speed crash. When short circuit, the voltage and current very large and original internal parts will damage.

The page contains the contents of the machine translation.