Mar 20, 2019 Pageview:1218
Ammeter had ascended to move turn knob ammeter that rotary switch contact undesirable.
Charging current is generally the battery one over ten of the volume. Just starting current is big because of low battery voltage. As the charging time increase, The battery voltage will increase. So the current is small. Generally do not adjust the current size, as long as with voltage meter measure the voltage of the battery. If the voltage reached 16 v, the electrolyte is charged. There are a lot of bubbles automatic charger is according to determine whether adequate electrical voltage. Can also make a such a device. Don't have to look at.
Battery charger, the correct way of using the battery charger is usually divided into automatic and manual charger, method of use: manual charger connection to charger (red) the positive (+) connection battery positive electrode (+);The cathode (black line) (-) connect the battery negative (-), automatic charger connection completed can open switch; After manual charger connection, will be charging voltage to 12 v or 24 v, then the charging current to 3 ~ 5, observe the charging current in 4 ~ 6 (24 v battery current 5 ~ 10) Ann can (pictured) automatic which is full of green light, manual when ammeter display is less than 0.5 A is filled.(as shown in figure)
Attention should be paid to the problem: 1) do not connect the battery charger is negative line connect the battery;2) connect the battery first followed by the utility can be open after check and correct the charging switch;3) to check the battery before charging, charging don't exceed the standard calibration (see chart);4) charging mouth not to shut down to prevent a gas charging the battery fluid overflow.
Manual charger using method: manual charger connection to charger (red) the positive (+) to connect battery positive electrode (+);The cathode (black line) (-) connect the battery negative (-).After manual charger connection, will be charging voltage to 12 v or 24 v, then the charging current to 3 ~ 5, observe the charging current in 4 ~ 6 (24 v battery current 5 ~ 10) Ann can automatic city which is full of green light.
Fully automatic charger connection can open the switch, manual when ammeter display is less than 0.5 A is filled. Pay attention to the problem:
1) do not connect the battery charger is negative line connect the battery.
2) after the battery first after checked mains switch on charging.
3) to check the battery before charging, charging don't exceed the standard calibration (see chart);4) charging mouth not to shut down to prevent a gas charging the battery fluid overflow. Other answer
Battery charger, the correct way of using the battery charger is usually divided into automatic and manual charger, method of use: manual charger connection to charger (red) the positive (+) connection battery positive electrode (+);The cathode (black line) (-) connect the battery negative (-), automatic charger connection completed can open switch; After manual charger connection, will be charging voltage to 12 v or 24 v, then the charging current to 3 ~ 5, observe the charging current in 4 ~ 6 (24 v battery current 5 ~ 10) Ann can (pictured) automatic which is full of green light, manual when ammeter display is less than 0.5 A is filled.(as shown in figure)
Attention should be paid to the problem: 1) do not connect the battery charger is negative line connect the battery;2) connect the battery first followed by the utility can be open after check and correct the charging switch;3) to check the battery before charging, charging don't exceed the standard calibration (see chart);4) charging mouth not to shut down to prevent a gas charging the battery fluid overflow.
Manual battery charger
Automatic battery charger
Battery charging standard calibration line diagram
First check by charging the battery voltage and charging machine whether consistent; The charging voltage of battery and charger, this charge is very safe. If be charging the battery voltage is higher than the charger is likely to cause the battery charger is not in electricity; Joined by charging the battery voltage is lower than the charge of mechanical and electronic pressure in without any measures under the premise of charging, can make the battery produce risk, are also likely to burn charger.
The page contains the contents of the machine translation.
Leave a message
We’ll get back to you soon